What are your thoughts concerning How to Install a Bathtub?
Setting up a bathtub isn't specifically rocket science, however it does require solid plumbing, woodworking, and also often, tiling skills. Changing an old tub with a brand-new one is additionally a reasonably hard task. If the old bathtub is easily accessible, the job can move easily; if you need to open up a wall surface to remove the old bathtub and also position the brand-new bath tub, the job is a lot harder. In either situation, the job is within a house handyman's abilities, although you will certainly require an assistant to move out the old bathtub and also set in the brand-new one. Make sure you have certified yourself for the job and also fit attempting it. Rather than hiring a service provider to take control of a halfway-completed job, it is better to take into consideration utilizing one prior to you begin. Chances are you might need a specialist plumber to make tube links.
This article will certainly aid you mount a new tub in your washroom if you have actually already bought a brand-new tub as well as don't need to transform the setup of your previous water pipes.
Your tools and also material checklist need to comprise the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you must do is separate the water system. After doing so, turn on the faucets to drain any water continuing to be in the system. The procedure of removing the existing taps can be rather problematic because of the restricted accessibility that is typically the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the taps. Have a fabric all set for the remaining water that will come from the pipes. As soon as the supply pipelines have actually been gotten rid of, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from turning throughout this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned of any old securing substance.
Before carrying on to fit the new faucets, contrast the pipeline links on the old taps to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will require a plastic adapter to stop damages to the string. One end of the connector fits on the plastic tail of the faucet and the other end supplies a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly need reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the placing hole in the bath/basin ensuring that the washers are in place in between the faucet as well as the sink. Secure the tap in place with the manufacturer given backnut. As soon as the faucet is safely in place, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal faucet adapters. The former kind must be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Bath tub
Making use of both wood boards under its feet, position the bath tub in the required placement. The wooden boards are valuable in uniformly spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 small points.
The following objective is to make sure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and also adjusting the feet on the bath tub until the spirit level reads degree.
To set up faucets, fit the bottom of the outermost adaptable tap adapter to the ideal supply pipeline by making a compression join; then do the same for the other faucet.
Switch on the supply of water as well as examine all joints and new pipework for leaks and tighten them if required. Fill the bathtub as well as additionally examine the overflow outlet and also the normal outlet for leakages.
Lastly, fix the bath paneling as described in the producer's instruction manual. Tiling and securing around the tub needs to wait up until the bath tub has actually been made use of a minimum of when as this will settle it into its final position.
Planning for the Installment
To start with, the sustaining frame provided with the bath must be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to ensure that if the faucet features a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets system to stop pressure on the tub.
Fit the versatile tap connectors to the bottom of the two faucets utilizing 2 nuts and olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you utilize all of the provided washing machines.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its last setting.
Tiling Around the Tub
In the location where the bath meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to fracture a rigid seal, triggering the water to permeate the wall surface in between the bath and the tiling, bring about problems with wetness and also feasible leakages to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, as well as are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealer can fracture rather early if you do not consider this motion before securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly available on the market. It is suggested to fit the ceramic tiles utilizing waterproof or water resistant adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a devoted person who reads about Installing A Bathtub, I imagined sharing that segment was a smart idea. Sharing is caring. Helping others is fun. I praise you for your time. Don't forget to stop by our site back soon.
Immediate help? Ring!